This is the table we would ask a supplier for if we were the buyer. Put it next to the drawing you buy against today: if the columns match, nothing else needs to change on your line.
| Model | Series | Shaft | Tip | Head Ø | Head len | O/L | Shaft Ø | Shaft len | Pcs/pack | Packs/box | Boxes/ctn |
|---|---|---|---|---|---|---|---|---|---|---|---|
| CS15-001 | CS15 fine | Paper | Spherical | φ3.2±0.5 | 12±1.0 | 76±1.0 | φ1.57±0.1 | 73±0.5 | 25 | 100 | 20 |
| CS15-002 | CS15 fine | Paper | Spherical | φ2.6±0.5 | 12±1.0 | 75±1.0 | φ1.57±0.1 | 73±0.5 | 25 | 100 | 20 |
| CS15-003 | CS15 fine | Paper | Tapered | φ3.0±0.5 | 10±1.0 | 78±1.0 | φ1.57±0.1 | 73±0.5 | 25 | 100 | 20 |
| CS15-005 | CS15 fine | Paper | Turned-down | φ2.1±0.1 | 7±1.0 | 78±1.0 | φ1.57±0.1 | 73±0.5 | 25 | 100 | 20 |
| CS15-006 | CS15 fine | Paper | Flat-trimmed | φ2.0±0.2 | 8±1.0 | 75.5±1.0 | φ1.57±0.1 | 73±0.5 | 25 | 100 | 20 |
| CS15-009 | CS15 fine | Paper | Ultra-fine | φ1.1±0.2 | 5±1.0 | 74±1.0 | φ1.57±0.1 | 73±0.5 | 25 | 130 | 20 |
| CS25-001 | CS25 coarse | Paper | Spherical | φ4.5 | 4.5+0.4/-0.2 | 76.0±0.8 | φ2.46±0.08 | 73.0±0.5 | 25 | 50 | 20 |
| CS25-002 | CS25 coarse | Paper | Spherical | φ4.7 | 4.7±0.5 | 81±1.0 | φ2.46±0.08 | 73±0.5 | 25 | 50 | 20 |
| CS25-003 | CS25 coarse | Knurled hardwood | Spherical | φ4.7 | 4.7±0.4 | 150.0±0.5 | φ2.3±0.1 | 148.0±0.5 | 100 | 10 | 20 |
| CS25-005 | CS25 coarse | Paper | Spherical | φ4.6 | 4.6±0.5 | 149.5±1.0 | φ2.46±0.08 | 146±0.5 | 100 | 10 | 20 |
| CS25-006 | CS25 coarse | Paper | Spherical | φ5.0 | 5.0±0.5 | 150.0±1.0 | φ2.46±0.08 | 146±0.5 | 100 | 10 | 20 |
Dimensions in millimetres. Nominal value ± tolerance. Highlighted rows are the two models requested most often for fine-pitch and deep-reach work.
This is the working inspection sheet, not a marketing list. Dimensions are checked with a vernier caliper; appearance is a 100% visual check. If your incoming inspection uses a different method or a tighter limit, send it over and we will check to yours.
| # | Item | Acceptance | Method |
|---|---|---|---|
| 1 | Shaft material | Paper (CS15, CS25) · Knurled hardwood (CS25-003) | Visual |
| 2 | Head material | Long-staple cotton | Visual |
| 3 | Shaft length | 73.0 ± 0.5 mm (3-inch range) | Vernier caliper |
| 4 | Shaft diameter | φ1.57 ± 0.1 mm (CS15) · φ2.46 ± 0.08 mm (CS25) · φ2.3 ± 0.1 mm (CS25-003) | Vernier caliper |
| 5 | Overall length | Per model — see dimensional table | Vernier caliper |
| 6 | Head length | Per model — see dimensional table | Vernier caliper |
| 7 | Head diameter | Per model — see dimensional table; tolerance ±0.2 to ±0.5 mm | Vernier caliper |
| 8 | Tip-to-shaft end distance | Per model — 1.0 ± 0.5 to 2.5 ± 0.5 mm (this is what makes a swab 74–78 mm overall) | Probe |
| 9 | Appearance | No loose fibre, no stain, no deformation | Visual, 100% |
LPC (liquid particle count), NVR (non-volatile residue) and ionic contamination by ion chromatography are the three figures a technical buyer asks for first. We do not hold current reports for them.
Report numbers are given so you can ask SGS to confirm them. Note what these cover: RoHS ten substances and halogen four. They are not particle, residue or ionic data, and we do not present them as such.
Our own label is printed in Chinese, English and Japanese — the three languages our existing distributors ship into. Swap it for yours and the plate change is on us: your brand, your part number, your barcode, your batch convention.
We will confirm fit model by model, or tell you where we differ — before you spend money on samples. If it lines up, we send a benchmark kit: three models, three packs each, and a comparison card with a blank column for your own limits.